Explore topic-wise fullforms in Electronics

In electrical engineering, low voltage is a relative term, the definition varying by context. Different definitions are used in electric power transmission and distribution, and electrical safety codes define "low voltage" circuits that are exempt from the protection required at higher voltages. These definitions vary by country and specific codes or regulations.

INFO: Full form for LV is Latent Variable in Electronics category
LV also has other full forms in other categories mentioned below.

A magnetic field is a vector field that describes the magnetic influence on moving electric charges, electric currents,: ch1 and magnetic materials. A moving charge in a magnetic field experiences a force perpendicular to its own velocity and to the magnetic field.: ch13 A permanent magnet's magnetic field pulls on ferromagnetic materials such as iron, and attracts or repels other magnets. In addition, a magnetic field that varies with location will exert a force on a range of non-magnetic materials by affecting the motion of their outer atomic electrons. Magnetic fields surround magnetized materials, and are created by electric currents such as those used in electromagnets, and by electric fields varying in time. Since both strength and direction of a magnetic field may vary with location, it is described mathematically by a function assigning a vector to each point of space, called a vector field.

In electromagnetics, the term "magnetic field" is used for two distinct but closely related vector fields denoted by the symbols B and H. In the International System of Units, H, magnetic field strength, is measured in the SI base units of ampere per meter (A/m). B, magnetic flux density, is measured in tesla (in SI base units: kilogram per second2 per ampere), which is equivalent to newton per meter per ampere. H and B differ in how they account for magnetization. In a vacuum, the two fields are related through the vacuum permeability, B / μ 0 = H {\displaystyle \mathbf {B} /\mu _{0}=\mathbf {H} } ; but in a magnetized material, the terms differ by the material's magnetization at each point.

Magnetic fields are produced by moving electric charges and the intrinsic magnetic moments of elementary particles associated with a fundamental quantum property, their spin.: ch1 Magnetic fields and electric fields are interrelated and are both components of the electromagnetic force, one of the four fundamental forces of nature.

Magnetic fields are used throughout modern technology, particularly in electrical engineering and electromechanics. Rotating magnetic fields are used in both electric motors and generators. The interaction of magnetic fields in electric devices such as transformers is conceptualized and investigated as magnetic circuits. Magnetic forces give information about the charge carriers in a material through the Hall effect. The Earth produces its own magnetic field, which shields the Earth's ozone layer from the solar wind and is important in navigation using a compass.

In telephony, multi-frequency signaling (MF) is a type of signaling that was introduced by the Bell System after World War II. It uses a combination of audible tones for address (telephone number) transport and supervision signaling on trunk lines between central offices. The signaling is sent in-band over the same channel as the bearer channel used for voice traffic.

Multi-frequency signaling defines electronic signals that consist of a combination of two audible frequencies, usually selected from a set of six frequencies. Over several decades, various types of MF signaling were developed, including national and international varieties. The CCITT standardization process specified the American Bell System version as Regional Standard No. 1, or Signalling System R1, and a corresponding European standard as Signalling System R2. Both were largely replaced by digital systems, such as Signalling System 7, which operate out-of-band on a separate data network.

Because of the in-band transmission characteristic of MF signaling, the systems proved vulnerable to misuse and fraud by phone phreaking with devices such as a blue box.

Multifrequency signaling is a technological precursor of dual-tone multi-frequency signaling (DTMF, Touch-Tone), which uses the same fundamental principle, but was used primarily for signaling address information and control signals from a user's telephone to the wire-center's Class-5 switch. DTMF uses a total of eight frequencies.

A mass flow controller (MFC) is a device used to measure and control the flow of liquids and gases. A mass flow controller is designed and calibrated to control a specific type of liquid or gas at a particular range of flow rates. The MFC can be given a setpoint from 0 to 100% of its full scale range but is typically operated in the 10 to 90% of full scale where the best accuracy is achieved. The device will then control the rate of flow to the given setpoint. MFCs can be either analog or digital. A digital flow controller is usually able to control more than one type of fluid whereas an analog controller is limited to the fluid for which it was calibrated.

All mass flow controllers have an inlet port, an outlet port, a mass flow sensor and a proportional control valve. The MFC is fitted with a closed loop control system which is given an input signal by the operator (or an external circuit/computer) that it compares to the value from the mass flow sensor and adjusts the proportional valve accordingly to achieve the required flow. The flow rate is specified as a percentage of its calibrated full scale flow and is supplied to the MFC as a voltage signal.

Mass flow controllers require the supply gas or liquid to be within a specific pressure range. Low pressure will starve the MFC of fluid and cause it to fail to achieve its setpoint. High pressure may cause erratic flow rates.

INFO: Full form for MS is Multiple Surface in Electronics category
MS also has other full forms in other categories mentioned below.

INFO: Full form for MS is Multi-spectral in Electronics category
MS also has other full forms in other categories mentioned below.

In fluid dynamics, laminar flow is characterized by fluid particles following smooth paths in layers, with each layer moving smoothly past the adjacent layers with little or no mixing. At low velocities, the fluid tends to flow without lateral mixing, and adjacent layers slide past one another like playing cards. There are no cross-currents perpendicular to the direction of flow, nor eddies or swirls of fluids. In laminar flow, the motion of the particles of the fluid is very orderly with particles close to a solid surface moving in straight lines parallel to that surface.Laminar flow is a flow regime characterized by high momentum diffusion and low momentum convection.

When a fluid is flowing through a closed channel such as a pipe or between two flat plates, either of two types of flow may occur depending on the velocity and viscosity of the fluid: laminar flow or turbulent flow. Laminar flow occurs at lower velocities, below a threshold at which the flow becomes turbulent. The velocity is determined by a dimensionless parameter characterizing the flow called the Reynolds number, which also depends on the viscosity and density of the fluid and dimensions of the channel. Turbulent flow is a less orderly flow regime that is characterized by eddies or small packets of fluid particles, which result in lateral mixing. In non-scientific terms, laminar flow is smooth, while turbulent flow is rough.

The Federal Aviation Administration (FAA) is the largest transportation agency of the U.S. government and regulates all aspects of civil aviation in the country as well as over surrounding international waters.: 12, 16  Its powers include air traffic management, certification of personnel and aircraft, setting standards for airports, and protection of U.S. assets during the launch or re-entry of commercial space vehicles. Powers over neighboring international waters were delegated to the FAA by authority of the International Civil Aviation Organization.

Created in August 1958, the FAA replaced the former Civil Aeronautics Administration (CAA) and later became an agency within the U.S. Department of Transportation.

INFO: Full form for CAF is Conductive Anodic Filaments in Electronics category
CAF also has other full forms in other categories mentioned below.

INFO: Full form for SLL is Side Lobe Level in Electronics category
SLL also has other full forms in other categories mentioned below.

Milli (symbol m) is a unit prefix in the metric system denoting a factor of one thousandth (10−3). Proposed in 1793, and adopted in 1795, the prefix comes from the Latin mille, meaning one thousand (the Latin plural is milia). Since 1960, the prefix is part of the International System of Units (SI).